790d www.vishay.com vishay sprague revision: 18-jun-12 1 document number: 42072 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 resin-molded, radial-lead solid tantalum capacitors features ? terminations: tin/lead (snpb), 100 % tin (sn) ? four case sizes precisel y molded with a flame retardant epoxy resin ? stand off on all case sizes ? available on tape fo r automatic insertion equipment (only a- and b-case, c- and d-case on request) ? low leakage current ?low impedance ? extended value ranges available ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 note * lead (pb)-containing terminations are not rohs-compliant. exemptions may apply. performance characteristics operating temperature: - 55 c to + 125 c (above 85 c, voltage derating is required) capacitance range: 0.1 f to 330 f capacitance tolerance: 10 %, 20 % voltage rating: 6.3 v dc to 50 v dc ordering information 790d 157 x0 006 r 2 p e3 model capacitance capacitance tolerance dc voltage rating case code style number packaging rohs compliant 790d = standard and extended range expressed in picofarads. the first two digits are the significant figures. the third is the number of zeros following. x0 = 20 % x9 = 10 % expressed in volts. to complete the three-digit block, zeros precede the voltage rating. a decimal point is indicated by an r (6r3 = 6.3 v) see ratings and case codes table insulated case (standard) see packing information b: bulk g: ammopack (h = 16.5 mm) h: ammopack (h = 18.5 mm) i: ammopack shouldered leads (a case) x: reel pack (h = 16.5 mm) y: reel pack (h = 18.5 mm) z: reel pack shouldered leads (a case) e3 = 100 % tin termination (rohs compliant) blank = snpb termination dimensions in inches [millimeters] case code h max. d max. t max. e 0.15 [0.006] ? 0.05 [0.002] (+ 10 %) a 0.287 [7.3] 0.185 [4.7] 0.165 [4.2] 0.100 [2.54] 0.020 [0.5] b 0.413 [10.5] 0.287 [7.3] 0.189 [4.8] 0.200 [5.08] 0.020 [0.5] c 0.413 [10.5] 0.484 [12.3] 0.287 [7.3] 0.400 [10.16] 0.024 [0.6] d 0.413 [10.5] 0.484 [12.3] 0.484 [12.3] 0.400 [10.16] 0.024 [0.6] 12 mm min. e t d 0.3 mm min. h ? +
790d www.vishay.com vishay sprague revision: 18-jun-12 2 document number: 42072 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 ratings and case codes c r (f) rated voltage u r at + 85 c 6.3 v 10 v 16 v 20 v 25 v 35 v 40 v 50 v category voltage u c at + 125 c 4.0 v 6.3 v 10 v 13 v 16 v 23 v 25 v 32 v std. ext. std. ext. std. ext. std. ext. std. ext. std. ext. std. ext. std. ext. 0.10 aa 0.15 aa 0.22 aa 0.33 a 0.47 a 0.68 a 1.0 aa 1.5 abb 2.2 a a b b 3.3 a a b a b 4.7 a a b b 6.8 a a b c 10 a b b c c 15 a b b b c c 22 a b b b c 33 b b c c d 47 b b c c d d 68 b c c 100 c d c d 150 c c d 220 c d 330 d standard ratings/extended ratings capacitance c r (f) case code part number max. dcl at + 25 c (a) max. df 120 hz, at + 25 c (%) max. impedance 100 khz, at + 25 c ( ? ) u r = 6.3 v dc at + 85 c, surge = 8 v; u c = 4 v dc at + 125 c, surge = 5 v 6.8 a 790d685x(1)6r3a2(2) 1.0 6 4.0 22 a 790d226x(1)6r3a2(2) 1.3 6 2.1 47 b 790d476x(1)6r3b2(2) 2.9 6 1.3 68 b 790d686x(1)6r3b2(2) 4.2 6 1.3 150 c 790d157x(1)6r3c2(2) 9.4 6 0.6 220 c 790d227x(1)6r3c2(2) 13.8 6 0.6 330 d 790d337x(1)6r3d2(2) 20.7 8 0.4 notes ? part number definitions: (1) insert 0 for 20 % to lerance or 9 for 10 % (2) see ordering information, packaging code ? extended ratings in bold print
790d www.vishay.com vishay sprague revision: 18-jun-12 3 document number: 42072 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 u r = 10 v dc at + 85 c, surge = 13 v; u c = 6.3 v dc at + 125 c, surge = 8 v 4.7 a 790d475x(1)010a2(2) 1.0 6 4.0 15 a 790d156x(1)010a2(2) 1.5 6 2.5 33 b 790d336x(1)010b2(2) 3.3 6 1.3 47 b 790d476x(1)010b2(2) 4.7 6 1.4 68 b 790d686x(1)010b2(2) 6.8 6 1.3 100 c 790d107x(1)010c2(2) 10.0 6 0.6 150 c 790d157x(1)010c2(2) 15.0 6 0.6 220 d 790d227x(1)010d2(2) 22.0 8 0.4 u r = 16 v dc at + 85 c, surge = 20 v; u c = 10 v dc at + 125 c, surge = 13 v 2.2 a 790d225x(1)016a2(2) 1.0 6 5.5 3.3 a 790d335x(1)016a2(2) 1.0 6 4.4 10 a 790d106x(1)016a2(2) 1.6 6 2.7 15 b 790d156x(1)016b2(2) 2.4 6 1.6 22 b 790d226x(1)016b2(2) 3.5 6 1.3 33 b 790d336x(1)016b2(2) 5.2 6 1.6 47 c 790d476x(1)016c2(2) 7.5 6 0.8 68 c 790d686x(1)016c2(2) 10.8 6 0.6 100 c 790d107x(1)016c2(2) 16.0 6 0.7 100 d 790d107x(1)016d2(2) 16.0 6 0.5 150 d 790d157x(1)016d2(2) 24.0 8 0.4 u r = 20 v dc at + 85 c, surge = 26 v; u c = 13 v dc at + 125 c, surge = 16 v 2.2 a 790d225x(1)020a2(2) 1.0 6 5.5 6.8 a 790d685x(1)020a2(2) 1.3 6 3.5 15 b 790d156x(1)020b2(2) 3.0 6 1.5 22 b 790d226x(1)020b2(2) 4.4 6 2.1 47 c 790d476x(1)020c2(2) 9.4 6 0.7 68 c 790d686x(1)020c2(2) 13.6 6 0.8 100 d 790d107x(1)020d2(2) 20.0 6 0.7 u r = 25 v dc at + 85 c, surge = 32 v; u c = 16 v dc at + 125 c, surge = 20 v 1.5 a 790d155x(1)025a2(2) 1.0 6 6.0 4.7 a 790d475x(1)025a2(2) 1.1 6 4.5 10 b 790d106x(1)025b2(2) 2.5 6 1.6 15 b 790d156x(1)025b2(2) 3.7 6 2.4 22 b 790d226x(1)025b2(2) 5.5 6 2.1 33 c 790d336x(1)025c2(2) 8.2 6 0.8 47 d 790d476x(1)025d2(2) 11.8 6 1.0 u r = 35 v dc at + 85 c, surge = 45 v; u c = 23 v dc at + 125 c, surge = 29 v 3.3 a 790d335x(1)035a2(2) 1.2 6 6.0 10 b 790d106x(1)035b2(2) 3.5 6 2.6 33 c 790d336x(1)035c2(2) 11.6 6 1.3 standard ratings/extended ratings capacitance c r (f) case code part number max. dcl at + 25 c (a) max. df 120 hz, at + 25 c (%) max. impedance 100 khz, at + 25 c ( ? ) notes ? part number definitions: (1) insert 0 for 20 % to lerance or 9 for 10 % (2) see ordering information, packaging code ? extended ratings in bold print
790d www.vishay.com vishay sprague revision: 18-jun-12 4 document number: 42072 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 u r = 40 v dc at + 85 c, surge = 52 v; u c = 25 v dc at + 125 c, surge = 32 v 0.10 a 790d104x(1)040a2(2) 1.0 6 30.0 0.15 a 790d154x(1)040a2(2) 1.0 6 24.0 0.22 a 790d224x(1)040a2(2) 1.0 6 18.0 0.33 a 790d334x(1)040a2(2) 1.0 6 14.0 0.47 a 790d474x(1)040a2(2) 1.0 6 11.0 1.0 a 790d105x(1)040a2(2) 1.0 6 6.5 1.5 b 790d155x(1)040b2(2) 1.0 6 5.2 2.2 b 790d225x(1)040b2(2) 1.0 6 4.0 3.3 a 790d335x(1)040a2(2) 1.3 6 2.8 3.3 b 790d335x(1)040b2(2) 1.3 6 2.8 4.7 b 790d475x(1)040b2(2) 1.8 6 2.0 6.8 b 790d685x(1)040b2(2) 2.7 6 1.6 10 c 790d106x(1)040c2(2) 4.0 6 1.3 15 c 790d156x(1)040c2(2) 6.0 6 1.0 22 c 790d226x(1)040c2(2) 8.8 6 0.8 33 d 790d336x(1)040d2(2) 13.2 6 0.6 47 d 790d476x(1)040d2(2) 18.8 6 0.5 u r = 50 v dc at + 85 c, surge = 65 v; u c = 32 v dc at + 125 c, surge = 41 v 0.10 a 790d104x(1)050a2(2) 1.0 6 30 0.15 a 790d154x(1)050a2(2) 1.0 6 24 0.22 a 790d224x(1)050a2(2) 1.0 6 18 0.68 a 790d684x(1)050a2(2) 1.0 6 8.0 1.0 a 790d105x(1)050a2(2) 1.0 6 6.5 1.5 b 790d155x(1)050b2(2) 1.0 6 5.2 2.2 b 790d225x(1)050b2(2) 1.1 6 4.0 3.3 b 790d335x(1)050b2(2) 1.6 6 2.8 4.7 b 790d475x(1)050b2(2) 2.3 6 2.0 6.8 c 790d685x(1)050c2(2) 3.4 6 1.6 10 c 790d106x(1)050c2(2) 5.0 6 1.3 15 c 790d156x(1)050c2(2) 7.5 6 1.0 standard ratings/extended ratings capacitance c r (f) case code part number max. dcl at + 25 c (a) max. df 120 hz, at + 25 c (%) max. impedance 100 khz, at + 25 c ( ? ) notes ? part number definitions: (1) insert 0 for 20 % to lerance or 9 for 10 % (2) see ordering information, packaging code ? extended ratings in bold print
790d www.vishay.com vishay sprague revision: 18-jun-12 5 document number: 42072 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 maximum permissible ripp le voltage at + 25 c typical curves of impedance vs frequency 10 1 0.1 u rms 30 20 2 5 0.7 7 3 0.5 0.2 0.3 50 v 10 v 25 v 6.3 v 16 v 35/40 v 0.1k 0.5 1k 5 10k 50 100k 500 frequency in hz case size ?a? 10 1 0.1 u rms 30 20 2 5 0.7 7 3 0.5 0.2 0.3 0.1k 0.5 1k 5 10k 50 100k 500 frequency in hz case size ?b? 50 v 10 v 25 v 6.3 v 16 v 35/40 v 10 1 0.1 u rms 30 20 2 5 0.7 7 3 0.5 0.2 0.3 0.1k 0.5 1k 5 10k 50 100k 500 frequency in hz case size ?c? 50 v 10 v 25 v 6.3 v 16 v 35/40 v 10 1 0.1 u rms 30 20 2 5 0.7 7 3 0.5 0.2 0.3 0.1k 0.5 1k 5 10k 50 100k 500 frequency in hz case size ?d? 50 v 10 v 25 v 6.3 v 16 v 35/40 v frequency in hz 10 1 0.1 1k 10k 100k 1m 10m 100m 47 f 6.3 v 6.8 f 30 330 f 150 f 100 10 1 0.1 47 f 6.8 f 1f 22 f 35 v
790d www.vishay.com vishay sprague revision: 18-jun-12 6 document number: 42072 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) non preferred configuration on request only performance characteristics 1. operating temperature: - 55 c to + 85 c with rated voltage u r applied. + 85 c to 125 c with linear voltage derating to category voltage u c (see general information) applied. 2. capacitance and tolerance: capacitance measured at 100 hz and + 25 c shall be within the specified tolerance limits of the nominal rating. 3. reverse voltage: 15 % of rated voltage at + 25 c 5 % of rated voltage at + 85 c 4. surge voltage: 130 % of u r at + 85 c 130 % of u c at + 125 c 5. impedance at 100 khz: measured at + 20 c 5 c, impedance shall not exceed the values listed in datasheet. 6. stability at low and high temperatures: capacitance change with temperature, dissipation factor and dc leakage current shall not exceed the limits of the following table. 7. life test: 2000 h at + 85 c with rated voltage applied 2000 h at + 125 c with category voltage applied ? c/c ? 10 % of initial value il ? 1.25 initial limit df ? initial limit 8. humidity test: 56 days at + 40 c, 90 % relative humidity ? c/c ? 8 % of initial value il ? initial limit df ? initial limit 9. charge and discharge test: 1 million cycles at + 85 c, 0.5 s charge at u r 0.5 s discharge series resistance < 0.5 ? ? c/c ? 5 % of initial value il ? initial limit df ? initial limit 10. marking: top: rating and polarity front: type, date co de, sprague trademark packaging quantities case code reel x/y ammo g/h bulk b a 1000 1000 500 b 1000 1000 250 c 300 (1) 300 (1) 100 d 200 (1) 200 (1) 50 temp. capacitance change c r u r ? 1900 c r u r > 1900 dissipation factor i l leakage current - 55 c - 10 % 9 % - 11 % + 25 c - 6 % 0.01 c r x u r or 1 a whichever is greater 8 % + 85 c + 12 % 9 % 0.1 c r x u r or 10 a whichever is greater 11 % + 125 c + 15 % 12 % 0.125 c r x u r or 12.5 a whichever is greater 14 %
790d www.vishay.com vishay sprague revision: 18-jun-12 7 document number: 42072 for technical ques tions, contact: tantalum@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 tape and reel packing designations symbol dimensions (mm) pitch of component p 12.7 1.0 feed hole pitch p 0 12.7 0.3 tape width w 18 (+ 1/- 0.5) hold down tape width w 0 5.0 hole position w 1 9 (+ 0.75/-0.5) hold down tape position w 2 0 (+ 3/-0) feed hole diameter d 0 4.0 0.3 tape thickness t 0.5 0.2 component alignment ? h0 2 lead clinch height h 0 16.0 0.5 hole center to component center p 2 6.35 1.3 lead wire spacing feed hole center to wire center f p 1 case a 2.5 + 0.6/- 0.1 5.1 0.7 case b 5 + 0.6/- 0.1 3.85 0.7 case b 5 + 0.6/- 0.1 3.85 0.7 reel pack options h = 16.5 h = 18.5 x y z x y ammopack options h = 16.5 h = 18.5 g h i g h quantity per reel/box 1000 1000 1000 product information quick reference guide www.vishay.com/doc?40037 selector guide www.vishay.com/doc?49054 parameter comparison guide www.vishay.com/doc?40033 mounting of through-hole components www.vishay.com/doc?40108 frequently asked questions www.vishay.com/doc?40110 reel packing ammopacking w 2 w 0 w 1 w h 0 ? h 30 max. h p t p 2 p 1 f p 0 ? d sprague 191 201 320 to 330 329 - 331 ? 20 41 to 45 direction of unreel a and b cases only (meets iec 286-2)
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
mouser electronics authorized distributor click to view pricing, inventory, delivery & lifecycle information: vishay: ? 790D106X0025B2BE3? 790d156x9025b2b? 790d225x0050b2be3
|
